EduProd
EduProd
JEE PCM PLATFORM
📊 Dashboard
LEARN MODULE · SCHEMATIC MODE

Trace it. Derive it. Know it.

Every cluster below maps one schematic path — from first principles to the final equation. Expand a node to follow the full derivation trace.

⚡ INTEGRATED VIRTUAL LABORATORIES (5)
Open Subject Labs Catalog ↗
Banking And Loops
Stage ↗
Common Forces In Mechanics
Stage ↗
Free Body Diagram
Stage ↗
Friction Force
Stage ↗
Pulley System
Stage ↗
01

Force & Free-Body Diagrams

2 concepts · Foundational
2 nodes
01

Force & Free-Body Diagrams

Every mechanics problem begins by isolating the body and drawing its free body diagram (FBD) listing all external forces acting on it. Only then can Newton's second law ΣF = ma be applied reliably.

Key Idea
Always isolate the body and draw its free body diagram (FBD) showing every external force before applying ΣF = ma.
Boundary Trap
Confusing internal vs external forces or sign of work done in thermodynamics (W = PΔV vs −PΔV).
Application Note
For a block on an incline, the FBD shows weight mg (downward), normal N (perpendicular to the surface), and friction f (opposing motion); resolving mg into mg·sinθ and mg·cosθ lets you write the two force-balance equations.
🔬 VIRTUAL LAB Common Forces In Mechanics
Full Stage ↗
? Quick Concept Check

Which of the following forces should be included in the free body diagram of a box being pushed along a floor?

Answer: The applied force, weight, normal reaction, and friction — every external force acting on the box.

02

Force & Free-Body Diagrams — Numerical & Application

The standard kinematic equations assume constant acceleration. Near Earth's surface the free-fall acceleration g is essentially constant, so they apply even though the velocity changes sign at the apex.

Key Idea
The kinematic equations v = u + at, s = ut + (1/2)at², and v² = u² + 2as apply only when acceleration is constant in both magnitude and direction.
Boundary Trap
Applying kinematic formulas v = u + at when acceleration is non-constant.
Application Note
A freely falling body has constant a = g downward, so v = u + gt gives its speed at any instant even though the velocity changes direction at the top of its flight.
🔬 VIRTUAL LAB Common Forces In Mechanics
Full Stage ↗
? Quick Concept Check

For which of the following motions can the standard kinematic equations be applied directly?

Answer: A car starting from rest with constant acceleration.

02

The Law Of Inertia

2 concepts · Foundational
2 nodes
01

The Law Of Inertia

The passenger's body was moving at the bus speed. When the bus decelerates, the upper body resists that change and continues forward — inertia of motion — because no sufficient force acts on it at that instant.

Key Idea
Inertia is the tendency of a body to maintain its state of rest or uniform motion; when a vehicle brakes, the passenger's upper body continues forward (inertia of motion) unless a force acts.
Boundary Trap
Confusing internal vs external forces or sign of work done in thermodynamics (W = PΔV vs −PΔV).
Application Note
When a bus starts suddenly, a standing passenger jerks backward because the lower body moves with the bus while the upper body remains at rest (inertia of rest).
🔬 VIRTUAL LAB Banking And Loops
Full Stage ↗
? Quick Concept Check

Sparks fly off tangentially from the edge of a grinding wheel. This demonstrates which property?

Answer: Inertia of direction — the particles tend to move along the tangent to the circular path.

02

The Law Of Inertia — Numerical & Application

The pseudo (D'Alembert) force is F_pseudo = −m·a₀: its magnitude is the product of the body's mass and the frame's acceleration, and it points opposite to the frame acceleration.

Key Idea
A pseudo (D'Alembert) force is F_pseudo = −m·a₀: magnitude equals mass times frame acceleration, directed opposite to the frame's acceleration vector.
Boundary Trap
Applying kinematic formulas v = u + at when acceleration is non-constant.
Application Note
In a lift accelerating upward at a₀, an observer inside feels an extra downward pseudo force m·a₀, so the apparent weight becomes N = m(g + a₀).
🔬 VIRTUAL LAB Banking And Loops
Full Stage ↗
? Quick Concept Check

A simple pendulum hangs in a cart accelerating horizontally with acceleration a₀. At equilibrium the string makes angle θ with the vertical. What is tanθ?

Answer: a₀/g

03

Conservation Of Momentum

2 concepts · Foundational
2 nodes
01

Conservation Of Momentum

Linear momentum is conserved only when the net external force on the system is zero. Internal forces (e.g. during collision or explosion) act in equal-and-opposite pairs and never change the total momentum.

Key Idea
Total linear momentum of a system is conserved when the net external force is zero (ΣF_ext = 0); it holds independently along each axis.
Boundary Trap
Confusing internal vs external forces or sign of work done in thermodynamics (W = PΔV vs −PΔV).
Application Note
A gun and bullet system has zero external horizontal force during firing, so M·V_gun + m·v_bullet = 0, giving the recoil velocity V_gun = −(m/M)·v_bullet.
🔬 VIRTUAL LAB Banking And Loops
Full Stage ↗
? Quick Concept Check

A gun fires a bullet and recoils backward. Why does the much lighter bullet carry almost all of the explosive kinetic energy?

Answer: Because momentum is conserved and KE_gun/KE_bullet = m_bullet/M_gun, which is very small.

02

Conservation Of Momentum — Numerical & Application

Momentum is conserved whenever external forces are negligible, even in inelastic collisions. Kinetic energy is NOT conserved in a perfectly inelastic collision because some converts to heat and deformation.

Key Idea
In any collision, total linear momentum is conserved if external forces are negligible; kinetic energy is conserved only in perfectly elastic collisions.
Boundary Trap
Applying kinematic formulas v = u + at when acceleration is non-constant.
Application Note
In a bullet-block ballistic collision, momentum conservation gives the common velocity v = m·u/(M + m), but kinetic energy drops, so you must not equate initial and final kinetic energies.
🔬 VIRTUAL LAB Banking And Loops
Full Stage ↗
? Quick Concept Check

A stationary shell explodes into three fragments. What is the vector sum of the momenta of all three fragments immediately after the explosion?

Answer: Zero.

04

Equilibrium Of A Particle

2 concepts · Foundational
2 nodes
01

Equilibrium Of A Particle

Lami's theorem states F₁/sinα = F₂/sinβ = F₃/sinγ, where α, β, γ are the angles between the pairs of forces (each force is paired with the sine of the angle opposite it).

Key Idea
For three concurrent coplanar forces in equilibrium, Lami's theorem gives F₁/sinα = F₂/sinβ = F₃/sinγ, where α, β, γ are the angles between the pairs of forces.
Boundary Trap
Confusing internal vs external forces or sign of work done in thermodynamics (W = PΔV vs −PΔV).
Application Note
For a weight W suspended by two strings at angles θ₁ and θ₂, Lami's theorem gives each tension by matching the sine of the opposite angle to each force.
🔬 VIRTUAL LAB Banking And Loops
Full Stage ↗
? Quick Concept Check

Three forces in equilibrium can be represented as the three sides of a closed triangle taken in order. This is because:

Answer: Their vector sum is zero.

02

Equilibrium Of A Particle — Numerical & Application

Lami's theorem applies only to three coplanar, concurrent forces in equilibrium. Each force is proportional to the sine of the angle between the other two.

Key Idea
Lami's theorem applies only to three coplanar concurrent forces in equilibrium, relating each force to the sine of the angle between the other two.
Boundary Trap
Applying kinematic formulas v = u + at when acceleration is non-constant.
Application Note
For a traffic light of weight W held by two wires, identify the three forces (W and the two tensions) and apply the F/sin(angle) proportion.
🔬 VIRTUAL LAB Banking And Loops
Full Stage ↗
? Quick Concept Check

A particle is acted upon by three forces of magnitudes 3 N, 4 N, and 5 N in equilibrium. What can you conclude?

Answer: The 3 N and 4 N forces are perpendicular to each other.

05

Common Forces In Mechanics

2 concepts · Foundational
2 nodes
01

Common Forces In Mechanics

Static friction self-adjusts from 0 up to its maximum μ_s·N. Once the applied force exceeds this limit, motion starts and kinetic friction acts at the constant value μ_k·N, with μ_k < μ_s.

Key Idea
Static friction self-adjusts from 0 up to its maximum μ_s·N; once motion begins, kinetic friction acts at the constant value μ_k·N, and μ_k < μ_s.
Boundary Trap
Confusing internal vs external forces or sign of work done in thermodynamics (W = PΔV vs −PΔV).
Application Note
The angle of repose is the largest angle at which a block stays put on an incline, given by tanθ_r = μ_s, since that is where the weight component just equals the limiting static friction.
🔬 VIRTUAL LAB Common Forces In Mechanics
Full Stage ↗
? Quick Concept Check

Which correctly orders the three types of friction coefficient?

Answer: μ_rolling < μ_kinetic < μ_static

02

Common Forces In Mechanics — Numerical & Application

Limiting static friction is μ_s·N = 0.4 × 20 = 8 N. Since the applied 5 N is below this limit, static friction simply equals 5 N and the block does not move.

Key Idea
Static friction is self-adjusting: if the applied force is less than μ_s·N, friction equals the applied force and the body stays at rest.
Boundary Trap
Applying kinematic formulas v = u + at when acceleration is non-constant.
Application Note
Here N = m·g = 20 N, so f_s(max) = 0.4 × 20 = 8 N. A 5 N push is less than 8 N, hence friction = 5 N.
🔬 VIRTUAL LAB Common Forces In Mechanics
Full Stage ↗
? Quick Concept Check

For the same block (μ_s = 0.4, μ_k = 0.3, m = 2 kg, g = 10 m/s²), what friction force acts when a horizontal force of 10 N is applied?

Answer: 6 N, the kinetic friction μ_k·N = 0.3 × 20.

06

Circular Motion

2 concepts · Foundational
2 nodes
01

Circular Motion

Uniform circular motion requires a net force toward the centre (centripetal). On a level road the only available horizontal force is static friction, f_s = m·v²/R.

Key Idea
For uniform circular motion a net force toward the centre (centripetal force) is required; on a level road it is provided by static friction, f_s = m·v²/R.
Boundary Trap
Confusing internal vs external forces or sign of work done in thermodynamics (W = PΔV vs −PΔV).
Application Note
Skidding begins when the required centripetal force m·v²/R exceeds the maximum static friction μ_s·m·g, giving the maximum safe speed v_max = √(μ_s·g·R).
🔬 VIRTUAL LAB Banking And Loops
Full Stage ↗
? Quick Concept Check

A cyclist rounds a curve of radius R at speed v. To avoid toppling, the cyclist leans inward. What is the lean angle θ with the vertical?

Answer: tanθ = v²/(R·g)

02

Circular Motion — Numerical & Application

For a frictionless banked road, N·sinθ = m·v²/R and N·cosθ = m·g. Dividing gives v = √(R·g·tanθ).

Key Idea
For a frictionless banked road, N·sinθ = m·v²/R and N·cosθ = m·g, giving the optimum speed v = √(R·g·tanθ).
Boundary Trap
Applying kinematic formulas v = u + at when acceleration is non-constant.
Application Note
A curve banked at 45° with R = 100 m (g = 10 m/s²) has optimum speed v = √(100 × 10 × 1) = 10√10 m/s.
🔬 VIRTUAL LAB Banking And Loops
Full Stage ↗
? Quick Concept Check

For a banked road, what is the relationship between the banking angle θ, speed v, and radius R?

Answer: tanθ = v²/(R·g)

07

Solving Problems In Mechanics

2 concepts · Foundational
2 nodes
01

Solving Problems In Mechanics

The first step is to isolate the body and draw its FBD showing only external forces. Internal forces between bodies act on different bodies and must not be added to one body's net force.

Key Idea
To solve a multi-body problem, isolate each body, draw its FBD showing only external forces, then apply Newton's second law along chosen axes.
Boundary Trap
Confusing internal vs external forces or sign of work done in thermodynamics (W = PΔV vs −PΔV).
Application Note
For two blocks in contact pushed by a force F, isolating the rear block shows the contact force as an external force on it, while the front block feels the equal-and-opposite reaction.
🔬 VIRTUAL LAB Common Forces In Mechanics
Full Stage ↗
? Quick Concept Check

For a row of blocks pushed by a force F, the contact force between two adjacent blocks depends on:

Answer: The masses of the blocks ahead of (being pushed by) that contact surface.

02

Solving Problems In Mechanics — Numerical & Application

Only the hanging weight m₂·g drives the system, and both masses accelerate together, so a = m₂·g/(m₁ + m₂).

Key Idea
For a table-pulley system the hanging weight provides the driving force, so a = m₂·g/(m₁ + m₂) and the tension is T = m₁·m₂·g/(m₁ + m₂).
Boundary Trap
Applying kinematic formulas v = u + at when acceleration is non-constant.
Application Note
With m₁ = 3 kg and m₂ = 1 kg (g = 10 m/s²), a = 10/4 = 2.5 m/s² and T = 3 × 1 × 10/4 = 7.5 N.
🔬 VIRTUAL LAB Common Forces In Mechanics
Full Stage ↗
? Quick Concept Check

For the same table-pulley system, which expression gives the string tension T?

Answer: T = m₁·m₂·g/(m₁ + m₂)