EduProd
EduProd
JEE PCM PLATFORM
📊 Dashboard
LEARN MODULE · SCHEMATIC MODE

Trace it. Derive it. Know it.

Every cluster below maps one schematic path — from first principles to the final equation. Expand a node to follow the full derivation trace.

⚡ INTEGRATED VIRTUAL LABORATORIES (4)
Open Subject Labs Catalog ↗
Ac Generator
Stage ↗
Ac Voltage Applied To A Resistor
Stage ↗
Ac Voltage Applied To A Series Lcr Circuit
Stage ↗
Representation Of Ac Current And Voltage
Stage ↗
01

AC Voltage & RMS Values

2 concepts · Foundational
2 nodes
01

AC Voltage & RMS Values

A plain average of a sinusoid over a full cycle is zero, so it cannot describe the heating. RMS is the square root of the mean of v², and I²R heating depends on i², giving a nonzero, physically meaningful DC-equivalent value V_rms = V0/√2.

Key Idea
V_rms = √(⟨v²⟩) = V0/√2; the full-cycle mean of a sinusoid is zero, so RMS (not the plain or half-cycle average) quantifies its DC heating equivalent.
Boundary Trap
Conflating the half-cycle average (2V0/π ≈ 0.637 V0) with the RMS value (V0/√2 ≈ 0.707 V0); RMS comes from the mean of v², not the mean of |v|.
Application Note
For a 220 V (rms) mains supply the peak is 220√2 ≈ 311 V, and a resistor dissipates the same heat as under a 220 V DC source.
🔬 VIRTUAL LAB Ac Voltage Applied To A Resistor
Full Stage ↗
? Quick Concept Check

A moving-coil DC galvanometer connected in an AC circuit reads zero, whereas a hot-wire ammeter reads the RMS current. Why?

Answer: The galvanometer deflection follows the instantaneous current (whose full-cycle average is zero), while hot-wire heating follows i² (whose mean is nonzero).

02

AC Voltage & RMS Values — Numerical & Application

Peak value V0 = V_rms × √2 = 220 × 1.414 ≈ 311 V.

Key Idea
V_peak = V_rms × √2 (and I_peak = I_rms × √2).
Boundary Trap
Dividing by √2 instead of multiplying when converting RMS to peak; V_peak = V_rms × √2.
Application Note
For a 220 V RMS supply, V_peak = 220 × 1.414 ≈ 311 V.
🔬 VIRTUAL LAB Ac Voltage Applied To A Resistor
Full Stage ↗
? Quick Concept Check

A sinusoidal AC voltage has a peak value of 314 V. Its average value over a positive half-cycle is approximately:

Answer: 200 V

02

Ac Voltage Applied To A Resistor

2 concepts · Foundational
2 nodes
01

Ac Voltage Applied To A Resistor

A resistor obeys Ohm's law v = iR at every instant, so if v = V0 sin(ωt) then i = (V0/R) sin(ωt): both peak and pass through zero at the same instants, giving zero phase difference.

Key Idea
In a pure resistor, v and i are in phase (φ = 0) because v = iR holds at every instant.
Boundary Trap
Applying the inductor/capacitor 90° phase shift to a pure resistor; only L and C introduce a phase difference, R does not.
Application Note
For v = V0 sin(ωt) across a resistor, i = (V0/R) sin(ωt), peaking and zeroing at the same instants.
🔬 VIRTUAL LAB Ac Voltage Applied To A Resistor
Full Stage ↗
? Quick Concept Check

The instantaneous power delivered to a pure resistor varies as p(t) = V0 I0 sin²(ωt). Its frequency relative to the source frequency f is:

Answer: Twice the source frequency (2f)

02

Ac Voltage Applied To A Resistor — Numerical & Application

P_avg = V_rms²/R = 220²/100 = 48400/100 = 484 W.

Key Idea
P_avg = V_rms²/R = I_rms² R = V_rms I_rms for a pure resistor.
Boundary Trap
Using the peak value or forgetting that RMS values are already the effective values to plug directly into P = V²/R.
Application Note
220²/100 = 48400/100 = 484 W.
🔬 VIRTUAL LAB Ac Voltage Applied To A Resistor
Full Stage ↗
? Quick Concept Check

The same 100 Ω resistor is connected to an AC source whose peak voltage is 220 V. The average power dissipated is:

Answer: 242 W

03

Representation Of Ac Current And Voltage

2 concepts · Foundational
2 nodes
01

Representation Of Ac Current And Voltage

A phasor is a vector of fixed length equal to the peak amplitude rotating at angular speed ω; its vertical component at any instant is the instantaneous sinusoidal value V0 sin(ωt).

Key Idea
A phasor's length is the peak amplitude and its vertical projection is the instantaneous value (V0 sin ωt).
Boundary Trap
Taking the phasor length as the RMS value; the phasor length is the peak (maximum) amplitude, while RMS is that length divided by √2.
Application Note
A phasor of length V0 at angle ωt has instantaneous value V0 sin(ωt), exactly reproducing the AC waveform.
🔬 VIRTUAL LAB Ac Voltage Applied To A Resistor
Full Stage ↗
? Quick Concept Check

A phasor that leads a reference phasor by angle φ appears on the phasor diagram:

Answer: Rotated counterclockwise by φ relative to the reference.

02

Representation Of Ac Current And Voltage — Numerical & Application

In-phase phasors point in the same direction and add algebraically: 3 V + 4 V = 7 V.

Key Idea
In-phase (φ = 0) phasors add as scalars; perpendicular (φ = 90°) phasors combine as √(V1² + V2²).
Boundary Trap
Using the 3-4-5 Pythagorean result for in-phase sources; the 5 V answer applies only when the two phasors are perpendicular (90° apart).
Application Note
3 V + 4 V in phase = 7 V; the 5 V (3-4-5) result arises only for a 90° phase difference.
🔬 VIRTUAL LAB Ac Voltage Applied To A Resistor
Full Stage ↗
? Quick Concept Check

Two alternating voltages of the same frequency, 3 V and 4 V peak, differ in phase by 90°. The peak value of their resultant is:

Answer: 5 V

04

Ac Voltage Applied To An Inductor

2 concepts · Foundational
2 nodes
01

Ac Voltage Applied To An Inductor

The back-EMF e = −L(di/dt) opposes changes in current, so the current reaches its peak a quarter-cycle after the voltage. In a pure inductor the current lags the applied voltage by 90° (ELI: voltage leads current).

Key Idea
In a pure inductor, current lags voltage by 90° (ELI: emf/voltage leads current).
Boundary Trap
Reversing the inductor lead/lag convention; for an inductor the voltage leads the current (current lags by 90°), the opposite of a capacitor.
Application Note
When v = V0 sin(ωt) is applied across an inductor, i = (V0/ωL) sin(ωt − π/2).
🔬 VIRTUAL LAB Ac Voltage Applied To A Resistor
Full Stage ↗
? Quick Concept Check

The average power consumed by a pure inductor over one complete cycle is:

Answer: Zero (wattless current)

02

Ac Voltage Applied To An Inductor — Numerical & Application

X_L = ωL = 2πfL = 2 × 3.14 × 50 × 0.1 = 31.4 Ω.

Key Idea
X_L = ωL = 2πfL, measured in ohms.
Boundary Trap
Omitting the factor 2π in X_L = 2πfL (using only fL), which under-counts the reactance.
Application Note
For L = 0.1 H at 50 Hz, X_L = 2 × 3.14 × 50 × 0.1 = 31.4 Ω.
🔬 VIRTUAL LAB Ac Voltage Applied To A Resistor
Full Stage ↗
? Quick Concept Check

The same inductor (X_L = 31.4 Ω) is connected to a 220 V (RMS), 50 Hz supply. The RMS current is approximately:

Answer: 7 A

05

Inductive Reactance

2 concepts · Foundational
2 nodes
01

Inductive Reactance

Since X_L = 2πfL, at f = 0 the reactance is zero (an ideal inductor is a short to steady DC), and as f grows X_L grows linearly, so an inductor suppresses high-frequency AC.

Key Idea
X_L = ωL = 2πfL: zero for DC (short circuit) and growing linearly with frequency (blocks high-frequency AC).
Boundary Trap
Reversing the DC/high-frequency limits of an inductor; X_L = 2πfL is zero for DC and infinite for infinite frequency.
Application Note
At f = 0, X_L = 0; as f → ∞, X_L → ∞, so inductors smooth high-frequency ripples.
🔬 VIRTUAL LAB Ac Generator
Full Stage ↗
? Quick Concept Check

Which best describes the graph of inductive reactance X_L plotted against frequency f?

Answer: A straight line through the origin

02

Inductive Reactance — Numerical & Application

From X_L = 2πfL, f = X_L/(2πL) = 125.6/(2 × 3.14 × 0.2) = 125.6/1.256 = 100 Hz.

Key Idea
f = X_L/(2πL).
Boundary Trap
Rearranging X_L = 2πfL incorrectly; the correct form is f = X_L/(2πL), not f = X_L × 2πL.
Application Note
f = 125.6/(2 × 3.14 × 0.2) = 100 Hz.
🔬 VIRTUAL LAB Ac Generator
Full Stage ↗
? Quick Concept Check

The same inductor (0.2 H) is now connected to a 200 Hz supply. Its new inductive reactance is:

Answer: 251.2 Ω

06

Ac Voltage Applied To A Capacitor

2 concepts · Foundational
2 nodes
01

Ac Voltage Applied To A Capacitor

Since charge q = C v, the current i = C(dv/dt) is the rate of change of voltage, so it peaks when the voltage is changing fastest (at its zero crossings). Hence the current leads the voltage by 90° (ICE).

Key Idea
In a pure capacitor, current leads voltage by 90° (ICE: current leads emf/voltage).
Boundary Trap
Reversing the capacitor lead/lag convention; for a capacitor the current LEADS the voltage by 90°, the opposite of an inductor.
Application Note
For v = V0 sin(ωt), i = V0 ωC cos(ωt) = V0 ωC sin(ωt + π/2).
🔬 VIRTUAL LAB Ac Voltage Applied To A Resistor
Full Stage ↗
? Quick Concept Check

The average power consumed by a pure capacitor over one complete cycle is:

Answer: Zero

02

Ac Voltage Applied To A Capacitor — Numerical & Application

X_C = 1/(2πfC) = 1/(2 × 3.14 × 50 × 10 × 10⁻⁶) = 1/0.00314 ≈ 318 Ω.

Key Idea
X_C = 1/(ωC) = 1/(2πfC), measured in ohms.
Boundary Trap
Forgetting to convert microfarads to farads (using C = 10 instead of 10 × 10⁻⁶), which shifts the result by six orders of magnitude.
Application Note
1/(2 × 3.14 × 50 × 10⁻⁵) = 1/0.00314 ≈ 318 Ω.
🔬 VIRTUAL LAB Ac Voltage Applied To A Resistor
Full Stage ↗
? Quick Concept Check

The same 10 μF capacitor is connected to a 220 V (RMS), 50 Hz supply. The RMS current is approximately:

Answer: 0.69 A

07

Ac Voltage Applied To A Series Lcr Circuit

2 concepts · Foundational
2 nodes
01

Ac Voltage Applied To A Series Lcr Circuit

The resistor voltage and the net reactance voltage (X_L − X_C) are 90° apart, so the impedance is the hypotenuse of the impedance triangle: Z = √[R² + (X_L − X_C)²].

Key Idea
Z = √[R² + (X_L − X_C)²]; the reactances oppose each other and are subtracted.
Boundary Trap
Adding the reactances (X_L + X_C) instead of subtracting them; the inductive and capacitive reactances oppose each other, so they subtract.
Application Note
With R, X_L and X_C in series, Z² = R² + (X_L − X_C)².
🔬 VIRTUAL LAB Ac Voltage Applied To A Resistor
Full Stage ↗
? Quick Concept Check

In a series LCR circuit, the phase angle φ between the applied voltage and the current is given by:

Answer: tan φ = (X_L − X_C)/R

02

Ac Voltage Applied To A Series Lcr Circuit — Numerical & Application

ω0 = 1/√(LC) = 1/√(2 × 8 × 10⁻⁶) = 1/√(16 × 10⁻⁶) = 1/(4 × 10⁻³) = 250 rad/s.

Key Idea
ω0 = 1/√(LC), and f0 = 1/(2π√(LC)).
Boundary Trap
Forgetting the square root (using 1/(LC)) or the unit conversion for microfarads.
Application Note
ω0 = 1/√(16 × 10⁻⁶) = 250 rad/s.
🔬 VIRTUAL LAB Ac Voltage Applied To A Resistor
Full Stage ↗
? Quick Concept Check

For the same circuit (L = 2 H, C = 8 μF), the resonant frequency f0 in hertz is (π = 3.14):

Answer: ≈ 39.8 Hz

08

Power Factor

2 concepts · Foundational
2 nodes
01

Power Factor

The power factor is the cosine of the phase angle, which from the impedance triangle is the adjacent side R over the hypotenuse Z: cos φ = R/Z.

Key Idea
Power factor cos φ = R/Z; it equals 1 for pure resistance or resonance and 0 for pure L or C.
Boundary Trap
Inverting the power factor as Z/R; cos φ is always R/Z, a value between 0 and 1.
Application Note
A purely resistive circuit has Z = R, giving cos φ = 1.
🔬 VIRTUAL LAB Ac Generator
Full Stage ↗
? Quick Concept Check

The apparent power S = V_rms I_rms differs from the true (average) power P_avg by:

Answer: A factor cos φ (P_avg = V_rms I_rms cos φ)

02

Power Factor — Numerical & Application

cos φ = R/Z = 40/50 = 0.8.

Key Idea
cos φ = R/Z.
Boundary Trap
Computing the power factor as Z/R (which exceeds 1); cos φ = R/Z is always at most 1.
Application Note
cos φ = 40/50 = 0.8 (φ ≈ 37°).
🔬 VIRTUAL LAB Ac Generator
Full Stage ↗
? Quick Concept Check

The same circuit (R = 40 Ω, Z = 50 Ω) carries an RMS current of 2 A at 100 V (RMS). The average (true) power is:

Answer: 160 W

09

Transformers

2 concepts · Foundational
2 nodes
01

Transformers

Voltage scales directly with the number of turns (V ∝ N), and, by energy conservation V_p I_p = V_s I_s, current scales inversely with voltage, giving V_s/V_p = N_s/N_p = I_p/I_s.

Key Idea
V_s/V_p = N_s/N_p = I_p/I_s (the transformation ratio k).
Boundary Trap
Writing current in the same direct proportion as voltage; current scales inversely with turns, so it is I_p/I_s = N_s/N_p.
Application Note
A step-up transformer (N_s > N_p) raises voltage but lowers current.
🔬 VIRTUAL LAB Ac Generator
Full Stage ↗
? Quick Concept Check

A transformer has 200 primary turns and 1000 secondary turns. This is a:

Answer: Step-up transformer with k = 5

02

Transformers — Numerical & Application

V_s = V_p × (N_s/N_p) = 220 × (500/5000) = 220 × 0.1 = 22 V.

Key Idea
V_s = V_p (N_s/N_p).
Boundary Trap
Inverting the turns ratio (using N_p/N_s instead of N_s/N_p), which would give 2200 V instead of 22 V.
Application Note
220 × 0.1 = 22 V.
🔬 VIRTUAL LAB Ac Generator
Full Stage ↗
? Quick Concept Check

The same ideal transformer draws a primary current of 0.5 A. The secondary current is approximately:

Answer: 5 A